Need some help with my he351

  • 12 Replies
  • 279 Views
*

Offline Clarkwisely

  • Member
  • **
  • 6
    • 97 12v 5 speed 7x10
Need some help with my he351
« on: June 15, 2017, 07:24:11 PM »
Hello I have a 97 12v with the stand alone controller, wondering if someone could help me code, I have 120 hp injectors and 3.55 gears with 35s, I can't get my exhaust break to really hold or whistle  and can't get the turbo to light till like 2300rpms, any help will be greatly appreciated

*

Offline hakcenter

  • developer
  • Hero Member
  • *****
  • 623
    • 1998 12v Ram
Re: Need some help with my he351
« Reply #1 on: June 17, 2017, 07:57:58 AM »
Do you have the android app and syncd to the LBB ?

If you get no response from the brake pin, you may have the CAN BUS wires reversed

*

Offline Rx7man

  • Crazy guy
  • Hero Member
  • *****
  • 908
  • Jack of all trades
    • '94 Dodge dually
Re: Need some help with my he351
« Reply #2 on: June 17, 2017, 01:40:16 PM »
It sounds like the turbo is wide open, which happens when there's a communication fault (2300 is about when it spools if I have mine wide open too)  As hakcenter said, check the CAN bus wiring over, and power supply.

Oh, and welcome :)
'94 dodge, Colt Cam, head worked, NV5600, 3.55's, SB clutch, Ford manual hubs w. hawk brakes, custom flatdeck, custom aluminum bumper, cab off restoration, totally new engine, Mahle pistons @19:1..HE351VE with 67mm turbine and 67x95mm compressor
440hp/1000 ft lb @ 2400 RPM

*

Offline Clarkwisely

  • Member
  • **
  • 6
    • 97 12v 5 speed 7x10
Re: Need some help with my he351
« Reply #3 on: June 17, 2017, 05:14:25 PM »
It's not stuck wide open because if I flip the break on  and take off I can light it  fast and  then flip it off and were good if tryed sealing the wires

*

Offline Rx7man

  • Crazy guy
  • Hero Member
  • *****
  • 908
  • Jack of all trades
    • '94 Dodge dually
Re: Need some help with my he351
« Reply #4 on: June 17, 2017, 09:21:36 PM »
I'm not familiar with the official LilBB code (I run my own), but I think you ought to be able to open the serial monitor and see what it's doing
'94 dodge, Colt Cam, head worked, NV5600, 3.55's, SB clutch, Ford manual hubs w. hawk brakes, custom flatdeck, custom aluminum bumper, cab off restoration, totally new engine, Mahle pistons @19:1..HE351VE with 67mm turbine and 67x95mm compressor
440hp/1000 ft lb @ 2400 RPM

*

Offline hakcenter

  • developer
  • Hero Member
  • *****
  • 623
    • 1998 12v Ram
Re: Need some help with my he351
« Reply #5 on: June 20, 2017, 11:07:11 PM »
Clark join the semi closed beta for the Android App here : https://play.google.com/apps/testing/com.devnull.lbb from your Android device.

Connect to the LBB with pin code 9220, and let us know if it sync's up with any data. To me it kinda sounds like you may just need to adjust the curves if the brake is indeed working.

*

Offline Clarkwisely

  • Member
  • **
  • 6
    • 97 12v 5 speed 7x10
Re: Need some help with my he351
« Reply #6 on: August 24, 2017, 01:22:27 PM »
Should the break work in the performance  position
This what I'm getting

*

Offline hakcenter

  • developer
  • Hero Member
  • *****
  • 623
    • 1998 12v Ram
Re: Need some help with my he351
« Reply #7 on: August 24, 2017, 07:20:05 PM »
Yes if you look into the calculate modes section, brake is if'd last, so

if perf is on, or cruise is on but brake is on, brake will be the thing really done.


What are you looking to do ?

PS Position looks to be super way off.......

*

Offline Clarkwisely

  • Member
  • **
  • 6
    • 97 12v 5 speed 7x10
Re: Need some help with my he351
« Reply #8 on: August 24, 2017, 07:35:16 PM »
Ya turbo hasn't acted right since day one, don't spool very fast and exhaust break dose almost nothing  zero break effect

*

Offline hakcenter

  • developer
  • Hero Member
  • *****
  • 623
    • 1998 12v Ram
Re: Need some help with my he351
« Reply #9 on: August 24, 2017, 08:50:33 PM »
Try using my personal code.. Seems like an issue with the type of value used for position.

Also what version of Arduino IDE are you using ? May want to update to at least 1.8.2

*

Offline Clarkwisely

  • Member
  • **
  • 6
    • 97 12v 5 speed 7x10
Re: Need some help with my he351
« Reply #10 on: August 25, 2017, 03:26:28 AM »
I have your stand a lone system

*

Offline hakcenter

  • developer
  • Hero Member
  • *****
  • 623
    • 1998 12v Ram
Re: Need some help with my he351
« Reply #11 on: August 26, 2017, 11:44:20 PM »
I do believe this is resolved :D

*

Offline Rx7man

  • Crazy guy
  • Hero Member
  • *****
  • 908
  • Jack of all trades
    • '94 Dodge dually
Re: Need some help with my he351
« Reply #12 on: August 28, 2017, 12:55:50 AM »
Good news :)
'94 dodge, Colt Cam, head worked, NV5600, 3.55's, SB clutch, Ford manual hubs w. hawk brakes, custom flatdeck, custom aluminum bumper, cab off restoration, totally new engine, Mahle pistons @19:1..HE351VE with 67mm turbine and 67x95mm compressor
440hp/1000 ft lb @ 2400 RPM