Author Topic: Testing the actuator without the controller?  (Read 107 times)

Offline Turboedmav

  • Member
  • **
  • Posts: 7
    • 94 Thunderbird.
on: September 27, 2018, 07:33:32 AM
Is it possible to run some simple tests with a 12v source and/or a multimeter to find out whether an actuator is good or not?

I have the one installed on the HE300VG and an "orphan" from an HE351VE that I'd like to sell on eBay (but I want to know for sure if it's not fried)

Thanks...  :)



Offline hakcenter

  • developer
  • Hero Member
  • *****
  • Posts: 723
    • 1998 12v Ram
Reply #1 on: October 01, 2018, 08:14:53 PM
No way to really test it without sending it can commands.

I've ran across a few that powered up but didn't respond to commands.

AMP 2 Corinthians 8:21
For we take thought beforehand and aim to be honest and absolutely above suspicion, not only in the sight of the Lord but also in the sight of men.



Offline Rx7man

  • Crazy guy
  • Hero Member
  • *****
  • Posts: 1014
  • Jack of all trades
    • '94 Dodge dually
Reply #2 on: October 03, 2018, 11:22:05 AM
I think they move a little when they initially power up don't they?  Perhaps if you had the hot side off and tried to move the vanes while it's power vs unpowered you'd be able to tell that it's pushing back or not.. that's about all you can do.

'94 dodge, Colt Cam, head worked, NV5600, 3.55's, SB clutch, Ford manual hubs w. hawk brakes, custom flatdeck, custom aluminum bumper, cab off restoration, totally new engine, Mahle pistons @19:1..HE351VE with 67mm turbine and 67x95mm compressor
440hp/1000 ft lb @ 2400 RPM


Offline hakcenter

  • developer
  • Hero Member
  • *****
  • Posts: 723
    • 1998 12v Ram
Reply #3 on: October 06, 2018, 06:25:03 PM
Ya but all you'll know is the motor is good, not really the canbus side /shrug

AMP 2 Corinthians 8:21
For we take thought beforehand and aim to be honest and absolutely above suspicion, not only in the sight of the Lord but also in the sight of men.



Offline Rx7man

  • Crazy guy
  • Hero Member
  • *****
  • Posts: 1014
  • Jack of all trades
    • '94 Dodge dually
Reply #4 on: October 10, 2018, 08:27:36 PM
Ya but all you'll know is the motor is good, not really the canbus side /shrug
true indeed..
I don't know what the most common failure modes are on these.. I did see someone with a fried board, (was that Me23242?) that one certainly wouldn't move at all.

'94 dodge, Colt Cam, head worked, NV5600, 3.55's, SB clutch, Ford manual hubs w. hawk brakes, custom flatdeck, custom aluminum bumper, cab off restoration, totally new engine, Mahle pistons @19:1..HE351VE with 67mm turbine and 67x95mm compressor
440hp/1000 ft lb @ 2400 RPM


Offline hakcenter

  • developer
  • Hero Member
  • *****
  • Posts: 723
    • 1998 12v Ram
Reply #5 on: October 10, 2018, 10:33:54 PM
Ya burnt up the board

AMP 2 Corinthians 8:21
For we take thought beforehand and aim to be honest and absolutely above suspicion, not only in the sight of the Lord but also in the sight of men.



Offline Turboedmav

  • Member
  • **
  • Posts: 7
    • 94 Thunderbird.
Reply #6 on: October 13, 2018, 12:36:07 PM
Thanks for the replies guys... I guess I'll find out at least if the motors are good on my controllers, I have one from a HE351VE and the one on the HE300VG.