Lil' Blackbox

General => Hardware => Topic started by: hakcenter on August 13, 2017, 12:03:43 AM

Title: Another Hunt for Red October
Post by: hakcenter on August 13, 2017, 12:03:43 AM
HE300VG connectors :(

AMP MCP 2.8 HSG. 4POS.,ASS'Y: 1-1718628-1 AMP | TE Connectivity (http://www.te.com/usa-en/product-1-1718628-1.html)
Might just be on the right track.......

Actually this one...
4 POS TAB HSG ASSY CODE A: 1-699297-1 AMP | TE Connectivity (http://www.te.com/usa-en/product-1-699297-1.html)
Title: Re: Another Hunt for Red October
Post by: hakcenter on August 13, 2017, 07:18:15 PM
Clearly this is the male, on the HE300VG I have in front of me....

Coding A

Now to find the female....

Which looks exactly like the unit in Steed's picture... for the 2007-2013 models
Title: Re: Another Hunt for Red October
Post by: hakcenter on August 16, 2017, 06:26:36 PM
So the connector wiring is quite different, the outer 2 pins are power, the inner 2 are the canbus. However the HE300VG actuator uses the same exact addressing, so.. it runs just fine on the LBB.
Title: Re: Another Hunt for Red October
Post by: Rx7man on August 20, 2017, 04:46:32 AM
I hate looking for connectors.. just soo many different ones it drives me nuts.
Title: Re: Another Hunt for Red October
Post by: hakcenter on August 24, 2017, 08:08:49 PM
So hmm.. this looks just like the male and female.

How did you do that ? Dang, hard work searching ? No special Cummins contacts.. ? It's even keyed correctly ? Golly gee.
Title: Re: Another Hunt for Red October
Post by: me78569 on August 29, 2017, 06:57:29 PM
Do you happen to know the pin out for the 300ve turbo on late trucks?
Title: Re: Another Hunt for Red October
Post by: hakcenter on August 29, 2017, 10:42:33 PM
yep
Title: Re: Another Hunt for Red October
Post by: me78569 on August 30, 2017, 08:37:30 AM
Sharing is caring ? hahahah
Title: Re: Another Hunt for Red October
Post by: hakcenter on August 30, 2017, 06:15:34 PM
Sharing is caring ? hahahah
Tell Steed Dolan that.. dude refused to help, ignored me, ignored my customer. Then after a simple email, kinda you know... got angeryerereeed.

But yeah when I update the wiki, the connectors came in today, with various seal sizes, it uses the 5.2mm seal, comes in blue (super small awg) and red/brown (slightly larger awg)

holset_vgt [Lil' Blackbox] (http://wiki.lilbb.com/holset_vgt#he300vg)

I need to pigtail it, cause I left my phone at work and it had the layout :(

Just FYI it uses the same addressing, etc etc etc, it is all the same.
Title: Re: Another Hunt for Red October
Post by: me78569 on August 30, 2017, 07:30:43 PM
Yea he is not very helpful.  He is just mad that his method of tuning doesn't work near as well as yours.     

I give him props for the work he has done on various turbos, but the guy is not the type to share.   Hence why I link your site for people wanting a off the shelf type of controller rather than my DIY ugly mess of an article lol. 
Title: Re: Another Hunt for Red October
Post by: Rx7man on August 31, 2017, 02:56:10 PM
I have him on my FB, yeah, I didn't find he was very helpful either.. I wanted to know a little more about resetting position, etc
Title: Re: Another Hunt for Red October
Post by: hakcenter on August 31, 2017, 03:57:12 PM
Okay so the 300VG definitely will take values from 0 to 1000, not like 40 to 960 like the one on my truck..
Title: Re: Another Hunt for Red October
Post by: Rx7man on August 31, 2017, 09:50:56 PM
My 351 takes values from 0 to 1000, except anything above 960 is considered 1000
Title: Re: Another Hunt for Red October
Post by: hakcenter on August 31, 2017, 11:50:57 PM
There is a substantial diff from 960 to 990 to even 1000, so its 1000 points /shrug
Title: Re: Another Hunt for Red October
Post by: Rx7man on September 06, 2017, 09:27:28 AM
I think the firmware can be updated on them.. I think mine may have been done, since I seem to have a much longer timeout on comms failure (75ms) than what yours has
Title: Re: Another Hunt for Red October
Post by: hakcenter on September 08, 2017, 09:29:55 PM
Love to figure that one out... lol update muh firmwares plz
Title: Re: Another Hunt for Red October
Post by: Rx7man on September 09, 2017, 08:45:40 PM
A dodge dealer may be able to.. There was a guy selling a 351VE with no actuator who has all the tools, I think that came up in the discussion at some point
Title: Re: Another Hunt for Red October
Post by: ISGOIHowie on March 15, 2018, 10:46:42 AM
This is from Chryslers tech connect wiring diagram for a 2018 2500. EVERY other place in Chrysler cataloging is incorrect and shows the old connector.


I am a Chrysler Parts Adviser so if you guys have any other questions or need diagrams let me know.
Title: Re: Another Hunt for Red October
Post by: hakcenter on March 15, 2018, 02:15:58 PM
holset_vgt [Lil' Blackbox] (http://wiki.lilbb.com/holset_vgt#he300vg)

Kostal   9441491