Lil' Blackbox

General => Installation => Topic started by: Rx7man on October 08, 2015, 12:02:56 PM

Title: VGT connector pinouts
Post by: Rx7man on October 08, 2015, 12:02:56 PM
I know I saw them somewhere, but I can't find the VGT connector pinouts.. You should add them to the wiki

Als, I have some great 6 conductor wire, you think I can run the VR sensor and VGT  off the one bundle or do they really need to be physically separated/shielded?  Both CAN and the VR sensor are differential voltage systems, so I would guess they're pretty immune to noise.  Would make wiring far easier and neater.
Title: Re: VGT connector pinouts
Post by: hakcenter on October 08, 2015, 12:22:56 PM
The controller motor can pull 10amps so.. I would make sure your wire gauge is sized appropriately.

But don't worry about noise.
Title: Re: VGT connector pinouts
Post by: Rx7man on October 08, 2015, 12:46:00 PM
it's a fair size wire, better than most of the stuff dodge uses in the chassis!.. 18ga.

Got the pinouts?
Title: Re: VGT connector pinouts
Post by: hakcenter on October 08, 2015, 04:55:49 PM
Wires coming out of the Turbo
Brown/Gray:Smart Power Relay Feed
Black:Ground
Brown/Violet: CAN High
White/Light Green: CAN Low
Title: Re: VGT connector pinouts
Post by: Rx7man on October 08, 2015, 07:33:02 PM
Thanks
Title: Re: VGT connector pinouts
Post by: Rx7man on October 08, 2015, 07:35:55 PM
Oh, what does JP2 do?
Title: Re: VGT connector pinouts
Post by: hakcenter on October 09, 2015, 06:46:14 AM
JP2 is perf curve selection, +20 / +40 in the common
Title: Re: VGT connector pinouts
Post by: Rx7man on October 09, 2015, 09:12:53 AM
Thought that was JP1 (the 6 pin)
Title: Re: VGT connector pinouts
Post by: Rx7man on October 09, 2015, 09:19:41 AM
OH, and my wire colors are totally different.. Perhaps you can give me the terminal positions?

I got
Pin 1 = Red/blue stripe
Pin 2 = Green/white stripe
Pin 3 = Yellow
Pin 4 = Green

I think pin 1 and 4 are +12V and ground respectively, and the center two are CanH/L, but don't know which... I have Green/White stripe which I could guess as the 'new' version of White/green stripe
Title: Re: VGT connector pinouts
Post by: hakcenter on October 09, 2015, 03:15:14 PM
I'll have to look under the hood later for you, but if memory serves me, it was like +12v / GND / CAN / CAN

They did use weird colors...
Title: Re: VGT connector pinouts
Post by: Rx7man on October 09, 2015, 04:49:49 PM
and they switched them up it seem stoo... Mine says "Type II ECU RL" on it

looking at how the wires come out of the control box, the top row is green/white, red/blue, bottom row is green, yellow
Title: Re: VGT connector pinouts
Post by: me78569 on October 10, 2015, 10:01:29 AM
Yep its

Pin 1. Pwr
Pin 2. Gnd
Pin 3. Can
Pin 4. Can
Title: Re: VGT connector pinouts
Post by: Rx7man on October 13, 2015, 09:56:45 PM
OK, cool.. pin 3 CanL pin 4 CanH?
Title: Re: VGT connector pinouts
Post by: me78569 on October 14, 2015, 07:28:57 AM
here you go.

Title: Re: VGT connector pinouts
Post by: Rx7man on October 14, 2015, 08:56:52 AM
Excellent :).. thank you!
Title: Re: VGT connector pinouts
Post by: hakcenter on October 14, 2015, 05:56:55 PM
Ya sorry, been really busy working 8 to 4 at a water bottling plant running conduit and what not. Swamp coolers are barely working at all for the size of the warehouse, come home dreeeeeeeeeeeeeeenched.

But ya pin3 should be CanH
Title: Re: VGT connector pinouts
Post by: Rx7man on October 14, 2015, 09:55:53 PM
I got the harness made.. so far so good.. I'll see about testing it out at some point here, and making a box for it, and figuring out some terminal strip system  for my +5V bus, etc.