Main Menu

Recent posts

#91
Installation / Instructions on some things
Last post by Ravewolf - December 27, 2022, 05:07:29 PM
Is there by chance a guide to where everything goes or top-down pic of the Lil bb? I bought a shield and everything to put it together, but no idea where anything goes
#92
v2.0 / Re: Stuck in brake mode
Last post by Kookie - December 05, 2022, 08:39:53 AM
Sent an email.
#93
v2.0 / Re: Stuck in brake mode
Last post by hakcenter - December 05, 2022, 07:09:21 AM
Definitely going to need to setup a connection through your computer to see what's going on.

It is very interesting the latter hexs are not fully booting.

Email me directly and let's get something scheduled to look at this.
#94
v2.0 / Re: Stuck in brake mode
Last post by Kookie - December 04, 2022, 08:44:02 PM
Yes just using my phone with the app to update.
I csn get a computer to use if need be, will need help with all the aridunno stuff.
It completes the install but when trying to reconnect it gets stuck in the loop of waiting for reset
Flash older file and connects with no issue.
I havent really fiddled with the app once i was happy with my tune
#95
v2.0 / Re: Stuck in brake mode
Last post by hakcenter - December 04, 2022, 07:55:43 PM
Yes technically all the modes are activated sensing ground on their pullup pin.

We can write to ignore the pin if there's some problem going on.

Are you updating firmware from the Bluetooth app ?
#96
v2.0 / Re: Stuck in brake mode
Last post by Rx7man - December 04, 2022, 07:41:01 PM
without a computer to be able to see what's going on it's a little hard to diagnose.. I'm not that familiar with the stock Lil'bb code so I'm especially useless.. Hopefully Curtis will be here to give you a hand
#97
v2.0 / Stuck in brake mode
Last post by Kookie - December 04, 2022, 07:34:20 PM
Have intermittent  starter issus and now the truck is stuck in brake mode
At the time did not have the app with me to look at speed sensor reading
Tested out the harness for the controller, all good
Can bus checks out for high and low, powers and grounds and wiring to speed sensor
App says turbo is in brake mode, input wire disconnected to insure not the issue
Disconnected the JB jumper to no change
Updated from 3.00 to 3.03, going to 3.04 or 3.05 and the controller gets stuck waiting for reset messgae on app
Any sugestions?  Currently with out a computer
Have been daily driving truck and first issue since getting it all fully installed
It should only show brake mode if pin for the input is grounded?
#98
General Discussion / Re: Looking for info
Last post by hakcenter - November 27, 2022, 07:31:00 AM
The stand-alone does not need any additional inputs. The turbo comes equipped with the shaft speed sensor.

You can add additional inputs if you would prefer however you will need to write the additional code.

I left in a simple RPM counter on the spare pin that just needs uncommenting to count but to incorporate it into the size calculation will take some additional work.
#99
General Discussion / Looking for info
Last post by 98K35006BT - November 24, 2022, 04:14:05 PM
Hey All,

I got a 98 Chevy CCLB Dually I just put a 12V Cummins out of a 94 Ram into. I was thinking about running compounds until I came across this website.
I've been skimming through the info here and in the FAQ and while it's a trove of good usable info it's not very centralized. It's hard to find answers to basic questions that one may have. For example I'm wondering about inputs.
What all signals are needed by the standalone?

From what I can tell there's a throttle position signal and a VR signal needed. Is that all?

I had more questions but I forgot them. Lol
I'll edit and post more as I remember them. Thanks!
And Happy Thanksgiving!
#100
General Discussion / Re: Turbo Speed Measurement Is...
Last post by hakcenter - October 27, 2022, 12:24:43 PM
Do you have any back pressure equipment to verify a steady environment for the turbo ?
This is the second HE351VE I've heard of that has unstable shaft speeds, yet I just tuned Dooley and his turbo was rock solid shaft speed.

Can you provide some pictures of your soldering, verify your pinning on the max chip on the adapter board prior to soldering to the main board ?